BE.2c (Early Type) build | The Vintage Aviator


Latest News Projects Albatros DVa Build Gallery Covering The Albatros DVa FE.2b Flying the FE.2b Flight Video Build Gallery Fokker DVII Build Story The "Blue Max" SE.5a Reproduction Flying the SE.5a SE.5a History SE.5a Walkaround SE.5a Gallery Re.8 Reproduction RE.8 On Display RE.8 Gallery RE.8 History BE.2 Aircraft Be.2 History BE.2c (Early Type) build gallery BE2f Restoration BE2c Reproduction BE.2f Reproduction Bristol F2B Walkaround F2B History RAF.1a Engine RAF.1a Gallery RAF.1a History Beardmore Engine Beardmore Engine History Beardmore Engine Movie Beardmore Gallery Mercedes Engine Mercedes Engine History Gallery Oberursel Engine Oberursel Engine Movie Oberursel Gallery Sopwith Triplane Sopwith Triplane History Walkaround Gallery Sopwith Triplane Gallery Aircraft Guns Early Spandau Gun The Parabellum Gun The Us Savage Gun The Spandau LMG 08/15 The Lewis Gun The Schwarzlose Gun The Vickers Gun The Foster Mount Aircraft Gun Gallery Reference Covering with linen German Translations White Metal Bearings Irish Linen Cable Splicing Airshows TVAL Airshows ANZAC Day Airshow Remembrance Day 2008 Remembrance Day 2009 Classic Fighters 2007 2005 2003 2001 Mid-air Drama Warbirds Over Wanaka 2008 2006 2004 Wings over Wairarapa 2007 2005 Other Appearances Ferry Flights Hood Aerodrome 2007 1914-18 Photographs Album I Album II Album III Relics Uniforms 1914-18 Posters Posters - Album I Motion Pictures Models About Us The Vintage Aviator Ltd Terms and Conditions Site map Links Contact		BE.2 BE.2c (Early Type) build Home\| Projects\| BE.2 \| BE.2c (Early Type) build » Aft fuselage under construction note curvature in ash longerons BE.2c aft fuselage under construction Ash lower longerons in place as a strating point for the rest of the cockpit section to be built on. Laminating ash tip bows Wooden parts preserved with modern two part varnish and shellac Chris Higson installing fittings on aft fuselage section Early BE.2c wings, note RAF6 airfoil section Butt rib detail on lower wings Early BE.2c (foreground) and late style BE.2c Trial fit of skid type landing gear Elliot Eaton measures forward cockpit in order to fabricate fuel tank cover Assembled to measure interplane strut lengths and check rigging Cockpit looking forward Wing attach detail Engine mount detail Fuel tank details Simple windscreen layout Checking wing rigging Wings in place and rigged with temporary struts to check wire bracing lengths Unique BE.2c wing rib design Trial fit of wings Mike Grealish install cockpit details Fabric around cockpit is a sort of rubberized cotton, not leather Carefully guiding the engine onto its perch The Renault engine utilizes two tubular engine mounts seen extending out of the sides of the engine 80 HP Renault carefully lowered into place, not small flywheel on back of engine Original 80 HP Renault engine overhauled, tested and ready for installation Engine and upper fuel tank in place. Wicker observers seat is clearly visible here Final assembly of fuselage Paul installs fuselage fabric while Bruce fabricates the lower cowling Bruce Gibson starting to form lower cowl Rear turtle deck covered, side panels will be laced on and then cutouts made for elevator and rudder arms. Trial fit of fuselage side panel, note lacing After shrinking Irish linen with water the first coat of tautening dope can be applied In this early BE.2c the engine is almost completely exposed as seen here Completed engine installation, note minimal cowlings and under fuselage exhaust Engine installation details More on BE.2... BE.2f Restoration BE.2c Reproduction Be.2 History BE.2f Reproduction Back to top


© THEVINTAGEAVIATOR.CO.NZ CAA Approved