BE.2f Reproduction | The Vintage Aviator


Latest News Projects Aircraft Albatros DVa History Build Gallery Build Story Timelapse video Flying the Albatros In Flight Walkaround FE.2b Build Gallery Flying the FE.2b Flight Video Fokker DVII The "Blue Max" Build Story Fokker DVIII In Flight Sopwith Snipe In Flight SE.5a Reproduction SE.5a History SE.5a Gallery Flying the SE.5a SE.5a Walkaround Re.8 Reproduction RE.8 History RE.8 Gallery RE.8 On Display BE.2 Aircraft Be.2 Family History Build gallery BE2f Restoration BE2c Reproduction BE.2f Reproduction Bristol F2B F2B History Walkaround Sopwith Triplane History Gallery Walkaround Nieuport 11 Bebe Engines RAF.1a Engine RAF.1a History RAF.1a Gallery Beardmore Engine History Gallery Movie Mercedes Engine History Gallery Oberursel Engine Gallery Movie Aircraft Guns Early Spandau Gun The Parabellum Gun The Us Savage Gun The Spandau LMG 08/15 The Lewis Gun The Schwarzlose Gun The Vickers Gun The Foster Mount Aircraft Gun Gallery Wants & Disposals Reproduction Instruments Reference Covering The Albatros DVa Covering with linen German Translations White Metal Bearings Irish Linen Cable Splicing Airshows TVAL Airshows ANZAC Day 2011 ANZAC Day 2008 ANZAC Day 2010 Remembrance Day 2008 Remembrance Day 2009 Classic Fighters 2011 2007 2005 2003 2001 Mid-air Drama Warbirds Over Wanaka 2008 2006 2004 Wings over Wairarapa 2007 2005 Other Appearances Ferry Flights Hood Aerodrome 2007 Waipukurau Trip 1914-18 Photographs Album I Album II Album III Relics Uniforms 1914-18 Posters Posters - Album I Motion Pictures Models About Us The Vintage Aviator Ltd Terms and Conditions Site map Links Contact		BE.2 BE.2f Reproduction Home\| Projects\| Aircraft\| BE.2 \| BE.2f Reproduction » The makings of a BE2 BE2 strut fairings BE2e upper wing panel Leading edge detail Even original style markings are used Linen cord wrapping reinforces the joint between leading edge and wingtip bow Leading edge and false rib detail Completed BE2e upper wing Completed BE2e upper wing panel BE2e aileron under construction Completed BE2e outer aileron Completed aileron, note laminated spar which is routed internaly to reduce weight Wing walk area of lower wing The begining of a BE2 Joint between ash front longerons and the soon to be attached rear longerons Lower longeron detail Lower longeron detail Wing attach fitting Fuselage fitting detail Close up of fuselage fitting, note original style part number and inspection stamp Typical fuselage fitting First upright fuselage member installed Lower forward fuselage fitting Main flying wire attach fitting Steel fuselage uprights that support elevator control yokes Intermediate fuselage detail Intermediate fuselage detail Intermediate fuselage detail Forard fuslage fittings Main fuel tank installation Intermediate fuselage detail Ash lower longerons TVAL built main fuel tank in place Main fuel tank and upper longerons installed Fusleages are assembled on a fixture to aid in aligment and rigging Nearly complete forward fusleage section Forward fusleage section with engine mount tubes in place Control stick and elevator trim mechanism BE2c fuselage with main landing gear being installed Main landing gear detail Stabilizer attch detail note fabric to simulate covered parts Dion Hunter tests the new floorboards Pilots armoured seat Original style cockpit combing installed Dion is practicing to become an observer Detail of cockpit combing View through a BE2 Lower wings being fit to fuselage BE2c fuselage and BE2e wings constitute a BE2f Test fit of lower wings Landing gear and flying wire attach fitting Forward stabilizer attach Cast bronze elevator control horn Aft fuselage detail All major components must be assembled to check fits and clearances prior to covering All major components in place to check rigging The BE2f is large from any angle Levelling the airplane to prepare to check rigging More on BE.2... BE.2c (Early Type) build BE.2f Restoration BE.2c Reproduction Be.2 (Family) History Back to top


© THEVINTAGEAVIATOR.CO.NZ CAA Approved